Hermes STM32F405 Flight Controller
Robot / hardware buildMIT-licensed four-layer KiCad STM32F405RGT6 drone flight controller PCB with dual IMUs (MPU-6050 and ICM-20948), BMP280 barometer, 4x PWM ESC outputs, and LCSC-mapped JLCPCB manufacturing outputs; unfabricated and without firmware. [1] [2] [3] [4]
Build & first use →Official websiteSource codeUpstream build guideBill of materials
- For
- UAV hardware students, hobbyists, and embedded engineers studying or adapting a minimal four-layer STM32F405 KiCad flight controller. [1] [2]
- Cost
- No current cost yet. Upstream bill of materials [3]
- Source rights
- Named licenses are documented by part. Review licenses
- Unknowns
- host computer, operating system not fully established. Review gaps
Source researched · Not tested by us
Sources checked · Research details
Overview
Is this for you?
- Use cases
- Educational STM32F405 flight-controller PCB reference design
- Custom quadrotor flight controller fabrication after independent bring-up and firmware development
Inferred from README 4x PWM ESC outputs and pre-fabrication status.
- Known limitations
- Unfabricated and untested hardware: README explicitly states "Design is done and now it's onto fabricating the PCB and writing the firmware", with no commits since March 2025.
- No firmware source code, Betaflight/ArduPilot target definition, or pin-mapping configuration file is included in the repository.
- README lists "MPU-6050 / ICM-2098" (typo for ICM-20948), while bom.csv populates both U4 (MPU-6050) and U5 (ICM-20948) simultaneously alongside a 1.8 V LDO and NTS0104PW level shifter.
- Per-board JLCPCB fabrication and assembly cost is not published in the repository.
- Source review only: no KiCad ERC/DRC check, PCB fabrication, electrical bring-up, or flight test was performed.
What you need
Hardware & parts
Upstream bill of materials [3]
- Sensors
- MPU-6050 IMU (U4)
- ICM-20948 IMU (U5, powered via 1.8 V LD39015M18R LDO and NTS0104PW level shifter)
- BMP280 barometric pressure sensor (U8)
- Power
AP63203WU buck regulator (U2), LD39015M18R 1.8 V LDO (U6), AO3401A MOSFET (Q1), B5819W Schottky diode (D2), and 500 mA fuse (F1); maximum input battery voltage is not stated in README.
Assembly & first use
Open the upstream getting-started guide [2] · Project documentation [1]
Cost
No current, complete configuration-specific build cost has been established for this profile.
3D preview
Preview not available yet. A 3D CAD assembly preview has not been packaged for this hardware entry yet.
Model sources
A 3D CAD assembly preview has not been packaged for this hardware entry yet.
Project notes
What the KiCad package and LCSC BOM actually specify
Under PCB/HermesFC/, the repository contains the editable .kicad_pcb layout, three schematic sheets (HermesFC.kicad_sch, STM32.kicad_sch, Sensors.kicad_sch), custom switch footprint/symbol libraries, five component STEP models, and a JLCPCB-ready manufacturing folder (HermesFC-Gerber.zip, bom.csv, positions.csv, designators.csv, netlist.ipc). Exported schematic and PCB PDFs (PCB/Schematic-HermesFC.pdf, PCB/PCB-HermesFC.pdf) and component datasheets (PCB/Datasheets/) sit alongside PCB/HermesFC/ under PCB/. [2]
Cross-checking the root README against PCB/HermesFC/manufacturing/bom.csv clarifies a detail that matters before ordering: the README lists IMU Sensor: MPU-6050 / ICM-2098 (a typo for ICM-20948), whereas the 26-line LCSC-mapped BOM populates both MPU-6050 (U4, C24112) and ICM-20948 (U5, C726001) alongside the STM32F405RGTx MCU (U1, C15742), BMP280 barometer (U8, C83291), AP63203WU buck regulator (U2, C780769), LD39015M18R 1.8 V LDO (U6, C361025), NTS0104PW level shifter (U7, C2802637), USBLC6-2SC6 USB ESD protector (U3, C7519), and a 16 MHz crystal (Y1, C13738). Builders should verify whether both IMUs are intended to be populated simultaneously and confirm input-voltage limits from the schematic and AP63203 datasheet, since the README does not state a battery cell-count rating. [1] [3]
Unvalidated status, missing firmware, and review scope
Upstream explicitly notes in the README that design is complete and the next steps are fabricating the PCB and writing firmware, with no repository activity since March 13, 2025. No firmware source code, Betaflight/ArduPilot target file, or per-board PCBA price quote is included. This review inspected only the pinned revision (e9d71cad594f); no KiCad ERC/DRC run, board fabrication, bench bring-up, or flight test was performed. [1] [2] [4]
What we checked
Source review only at commit e9d71cad594f. Upstream has not fabricated or flight-tested this board. No ERC/DRC run or physical test was performed. No local image asset is bundled yet.
Not yet established
- Requirements: operating system, host computer
- A step-by-step setup summary
Updates
Source files and licenses
MIT-licensed four-layer KiCad STM32F405 flight controller with complete schematics, PCB layout, Gerbers, and LCSC BOM; scoped partial because firmware is absent and upstream has not yet fabricated or flight-tested the board.
| Layer | Availability / license |
|---|---|
| mechanical design | available · MIT Five 3D STEP/STP component models in PCB/HermesFC/3Dmodels/; no full assembled-board STEP export or enclosure CAD. [2] [4] |
| electronics | available · MIT Editable 4-layer KiCad PCB, three schematics (HermesFC.kicad_sch, STM32.kicad_sch, Sensors.kicad_sch), Gerber ZIP, LCSC BOM, positions.csv, and schematic/PCB PDFs. [2] [3] [4] |
| firmware | not found · License not fully assessed README states firmware has not yet been written; no firmware or target config is present. [1] |
| documentation | available · MIT README, PCB overview, exported schematic/PCB PDFs, layer renders, and component datasheets. [1] [2] [4] |
Standalone flight-controller PCB; ground-control software is external.
Flight controller hardware design; no ML model weights.
Flight controller hardware design; no datasets.
References
Each source links to the exact revision we read. “Used for” shows where this page relies on it.
- S001 aadilnaji/Hermes-FlightController README.md
STM32F405RGT6 KiCad flight controller overview, 4x PWM ESC outputs, UART/I2C/USB interfaces, MIT license note, and pre-fabrication/pre-firmware status.Revision, date & where cited
Aadil Naji · github.com · revision
e9d71ca· README.md at · Accessed Nov 21, 2026
Used for: Overview, Is this for you?, What you need, Hardware & parts and 5 more - S002 aadilnaji/Hermes-FlightController PCB/HermesFC/README.md
Confirms 4-layer PCB stackup and JLCPCB-compatible Gerber, BOM, and position manufacturing outputs; repository tree confirms 3 .kicad_sch sheets, 1 .kicad_pcb, 5 STEP models, and datasheets.Revision, date & where cited
Aadil Naji · github.com · revision
e9d71ca· PCB/HermesFC/README.md at · Accessed Nov 21, 2026
Used for: Overview, Is this for you?, What you need, Hardware & parts and 4 more - S003 aadilnaji/Hermes-FlightController PCB/HermesFC/manufacturing/bom.csv
26-line LCSC-mapped BOM confirming STM32F405RGTx, both MPU-6050 and ICM-20948 IMUs, BMP280 barometer, AP63203WU buck, LD39015M18R 1.8 V LDO, NTS0104PW level shifter, and USBLC6-2SC6 ESD protection.Revision, date & where cited
Aadil Naji · github.com · revision
e9d71ca· PCB/HermesFC/manufacturing/bom.csv at · Accessed Nov 21, 2026
Used for: Is this for you?, What you need, Hardware & parts, Assembly & first use and 2 more - S004 aadilnaji/Hermes-FlightController LICENSE
Root MIT License (Copyright 2025 Aadil Naji).Revision, date & where cited
Aadil Naji · github.com · revision
e9d71ca· LICENSE at · Accessed Nov 21, 2026
Used for: Overview, Unvalidated status, missing firmware, and review scope, Source files and licenses
Correction guidance · Discussion is not enabled · Profile format 0.8.0-draft.1
Change history
2026-11-21 — Initial source-reviewed Open Spec 0.8.0-draft.1 profile for Hardware Blind-Spot Batch 2.