LeRobot Humanoid Hardware (Biped Platform)
Robot / hardware buildOpen-source 3D-printed bipedal lower-body robot platform from Hugging Face using 12 RobStride CAN-FD actuators, Raspberry Pi 5, and public Onshape CAD. [1] [2]
Build & first use →Official websiteSource codeUpstream build guideBill of materials
- For
- Robotics researchers and hardware builders reproducing an open-source bipedal lower-body platform. [1] [2]
- Cost
- USD 2,635.84 upstream parts estimate [1] · checked Nov 21, 2026 · DetailsNot included: shipping, import duties, and local taxes, 3D printer, power supply/battery not itemized in table and upper-body hardware and more.
- Source rights
- Named licenses are documented by part. Review licenses
- Unknowns
- host computer, operating system not fully established. Review gaps
Source researched · Not tested by us
Sources checked · Research details
Licenses & related hardware
- Ecosystem
- LeRobot, Raspberry Pi
- License
- Apache-2.0 · Details by part
Overview
Hugging Face's lerobot-humanoid-hardware repository publishes the mechanical build files, bill of materials, wiring documentation, and pre-assembly motor commissioning scripts for a 3D-printed bipedal lower-body robot. The pinned revision explicitly scopes this release to the biped platform—torso, left leg, and right leg—while leaving upper-body hardware out of scope even though an upper body appears in the linked public Onshape CAD document. [1] [2]
Is this for you?
- Use cases
- Bipedal locomotion research
- Hardware prototyping for humanoid lower-body control
Inferred from repository scope and linked control runtime.
- Known limitations
- Upper-body hardware is explicitly out of scope in this repository iteration despite appearing in the linked Onshape document.
- Requires 12 purchased RobStride actuators whose internal firmware is external to this repository.
- Source review only: print tolerances, wiring, motor commissioning, and walking performance were not physically tested.
Scoped to the inspected upstream sources and verification performed.
What you need
Hardware & parts
Assembly & first use
Open the upstream getting-started guide [1] · Project documentation [1]
- Order buy parts from hardware/bom/bom_buy.csv.
- Print the 75 STL parts listed in docs/manufacturing/printing_guide.md.
- Commission and check every RobStride motor over CAN before mechanical assembly using hardware/config/commission_motor.py.
- Assemble mechanical subassemblies following docs/assembly/assembly_guide.md.
- Run wiring and first power-on checks via docs/electronics/check_wiring.md and docs/electronics/first_power_on.md.
- Assembly
3D-printed PLA+ structure (75 STL parts across torso and left/right leg subassemblies) joined with metric cylinder-head screws, ISO 7379 shoulder screws, bearings, Norelem spherical rod ends, and assembly pins.
Cost
| Version | Price |
|---|---|
| Upstream indicative parts and filament estimate for one LeRobot Humanoid biped platform. | USD 2635.84 [1] Parts estimate |
Global / US-EU reference vendors · Checked 2026-11-21
| Included | 12 RobStride actuators (O0/O2/O3/O5); Raspberry Pi 5; BNO055/BNO085 IMU; SAVVYCANFD 2CH adapter; Bearings, Norelem spherical joints, shoulder screws, fasteners, cables; ~3.5 kg PLA+ filament; 2.5 mm Allen key |
|---|---|
| Not included | Shipping, import duties, and local taxes; 3D printer, power supply/battery not itemized in table; Upper-body hardware; Assembly work |
| Stock | Component-sourced DIY build; vendor-dependent. |
| Delivery and tax | Excluded (shipping, import duties, and local taxes excluded by upstream). |
Price details
Upstream indicative estimate dated April 30, 2026 (EUR references converted at 1 EUR = 1.1691 USD on May 5, 2026): $2,579.84 BOM-to-buy subtotal plus $56.00 for ~3.5 kg PLA+ filament.
Global / US-EU reference vendors · Checked 2026-11-21 · Quantity 1
FDM 3D printer, battery/power supply and host workstation for control runtime.
Cost, licensing, and review gaps
The repository is licensed under Apache-2.0, while the bought-in RobStride actuators retain their own external firmware and hardware terms. Upstream publishes an itemized April 30, 2026 indicative BOM estimate of $2,635.84 USD ($2,579.84 for buy parts plus $56.00 for ~3.5 kg of PLA+). That total excludes shipping, import duties, taxes, a 3D printer, labor, and a battery or power supply (the required power-pack specification remains unverified), and current delivered supplier pricing has not been independently verified. This review inspected only the pinned repository files (8171f5799b04); no parts were printed, wired, commissioned, or walked. [1] [3]
3D preview
Preview not available yet. The upstream design is linked below. An interactive preview has not been prepared for this profile.
Model sources
The upstream design is linked below. An interactive preview has not been prepared for this profile.
Project notes
Hardware and fabrication scope
The printed structure consists of 75 STL parts organized by subassembly (torso, hipx, hipz, thigh, knee_mechanism, shin, ankle_mechanism, ankle, and foot) targeting roughly 3 to 4 kg of PLA+ filament. Actuation uses 12 bought-in RobStride CAN-FD actuators: two O0 units in the torso, two O2 units at hip yaw, four O3 units in the thighs, and four O5 units in the shins. Compute and sensing center on a Raspberry Pi 5, a BNO055 or BNO085 IMU, and a dual-channel SAVVYCANFD USB adapter. Mechanical joints rely on standard ball bearings, ISO 7379 shoulder screws, and Norelem spherical rod ends. [1] [4]
Before mechanical assembly, the build sequence requires running the repository's standalone hardware/config/commission_motor.py wizard over can0 to detect motor protocols, switch to MIT mode, assign model-based IDs, and verify motion without depending on robstride_toolkit. Robot models and control runtime live in a separate linked repository (Virgileboat/lerobot-humanoid-runtime). [1] [4]
What we checked
Source review only. No physical build, wiring check, or locomotion test was performed. No local image asset is bundled yet.
Not yet established
- Requirements: operating system, host computer
Updates
Source files and licenses
Includes a complete Apache-2.0 bipedal lower-body hardware design with printable STLs, public Onshape CAD, BOM, wiring docs, and motor commissioning scripts; partial openness because RobStride actuator internals/firmware and SBC/IMU modules are bought-in.
| Layer | Availability / license |
|---|---|
| mechanical design | available · Apache-2.0 75 exported STL files in repo plus public Onshape CAD document referenced in README. [1] [3] |
| electronics | available · Apache-2.0 Wiring diagrams, connector pinouts, and leg cabling docs are published under Apache-2.0; compute, IMU, CAN-FD adapter, and actuators are bought-in modules. [1] [3] [4] |
| firmware | not found · License not fully assessed RobStride actuator internal firmware is external/proprietary to the purchased motor modules and not published in this repository. [1] |
| software | available · Apache-2.0 Self-contained Python motor commissioning tool in repo; separate control runtime lives in Virgileboat/lerobot-humanoid-runtime. [1] [3] [4] |
| documentation | available · Apache-2.0 Assembly, printing, wiring, commissioning, and safety guides in docs/. [1] [3] |
This entry scopes the physical biped hardware repository rather than trained locomotion policies.
This entry scopes the physical biped hardware repository rather than datasets.
References
Each source links to the exact revision we read. “Used for” shows where this page relies on it.
- S001 huggingface/lerobot-humanoid-hardware README.md
Scope, Onshape CAD link, 75-part STL BOM, actuator/controller BOM, and April 30 2026 USD 2,635.84 cost estimate.Revision, date & where cited
Hugging Face · github.com · revision
8171f57· README.md at · Accessed Nov 21, 2026
Used for: Overview, Is this for you?, What you need, Hardware & parts and 5 more - S002 huggingface/lerobot-humanoid-hardware docs/overview.md
Scope boundary excluding upper body, CAD split, and traceability rules.Revision, date & where cited
Hugging Face · github.com · revision
8171f57· docs/overview.md at · Accessed Nov 21, 2026
Used for: Overview, Is this for you?, What you need, Hardware & parts - S003 huggingface/lerobot-humanoid-hardware LICENSE
Root Apache License 2.0 covering the repository.Revision, date & where cited
Hugging Face · github.com · revision
8171f57· LICENSE at · Accessed Nov 21, 2026
Used for: Cost, Source files and licenses - S004 huggingface/lerobot-humanoid-hardware docs/electronics/README.md
Wiring diagram, connector catalog, leg cabling diagrams, and standalone motor commissioning workflow.Revision, date & where cited
Hugging Face · github.com · revision
8171f57· docs/electronics/README.md at · Accessed Nov 21, 2026
Used for: Assembly & first use, Hardware and fabrication scope, Source files and licenses
Correction guidance · Discussion is not enabled · Profile format 0.7.0-draft.5
Change history
2026-11-21 — Initial source-reviewed draft for Hardware Blind-Spot Batch 1.