LEVIA-H7 Open-Source Flight Controller
Robot / hardware buildCERN-OHL-S-2.0 six-layer KiCad 10 STM32H743 UAV flight controller with dual ICM-42688-P IMUs, DPS368 barometer, IST8310 magnetometer, CAN, 8 motor outputs, and JLCPCB/NextPCB production exports. [1] [2] [3]
Build & first use →Official websiteSource codeUpstream build guideBill of materials
- For
- UAV hardware engineers, flight-controller designers, and aerial robotics researchers inspecting or fabricating open-hardware STM32H7 autopilots. [1]
- Cost
- No current cost yet. Upstream bill of materials [1] [2]
- Source rights
- Named licenses are documented by part. Review licenses
- Unknowns
- host computer, operating system not fully established. Review gaps
Source researched · Not tested by us
Sources checked · Research details
Licenses & related hardware
- License
- CERN-OHL-S-2.0 · Details by part
Overview
LEVIA-H7 is an original six-layer UAV flight controller designed in KiCad 10 by Pierluigi Colangeli and released under CERN-OHL-S-2.0. Built around an STM32H743VIHx microcontroller in a TFBGA-100 package, it is intended as a general-purpose open-hardware autopilot platform for multirotor, fixed-wing, and experimental aircraft rather than a clone of a commercial board. [1] [2] [3]
Is this for you?
- Use cases
- Multirotor UAV flight control
- Fixed-wing UAV flight control
- Experimental aerial robotics and PCB reference design
- Known limitations
- Explicitly unvalidated hardware design: upstream warns that prototype bring-up and flight testing are still pending.
- Requires KiCad 10 for local editing (or KiCanvas in a browser) and independent ERC/DRC/stackup verification before ordering.
- No flight-controller firmware source or board-specific hwdef PR is bundled in this hardware repository (MatekH743 ArduPilot peripheral conventions were used as reference).
- ESC connector pinouts are not universally standardized; VBAT, GND, and signal ordering must be verified before connecting an ESC.
What you need
Hardware & parts
Assembly & first use
Open the upstream getting-started guide [1] · Project documentation [1]
Cost
No current, complete configuration-specific build cost has been established for this profile.
Validation status, cost, and licensing
Upstream prominently warns that LEVIA-H7 is an unvalidated pre-production engineering revision: prototype bring-up and flight testing are still pending, and builders must independently review schematics, run ERC/DRC, verify controlled-impedance stackups, and check ESC pinouts before ordering or flying. No firmware or ArduPilot hwdef file is included in the repository (though MatekH743 peripheral conventions were consulted as a reference), and no per-board PCBA cost is published. All hardware files are released under the strongly reciprocal CERN-OHL-S-2.0 license. This review inspected only the pinned revision (8be94fc505d8); no ERC/DRC verification, PCB fabrication, or flight testing was performed. [1] [3]
3D preview
Preview not available yet. The upstream design is linked below. An interactive preview has not been prepared for this profile.
Model sources
The upstream design is linked below. An interactive preview has not been prepared for this profile.
Project notes
Hardware architecture and manufacturing files
The repository includes all 13 hierarchical .kicad_sch schematic sheets, the six-layer .kicad_pcb layout, custom design rules (.kicad_dru), exported schematic PDFs, a 3D STEP model (LEVIA_H7.step), board outline DXF, and production packages for both JLCPCB and NextPCB. The JLCPCB BOM specifies two ICM-42688-P IMUs on separate SPI buses, a DPS368 barometer, an IST8310 three-axis magnetometer, an AT7456E-compatible analog OSD IC, a SIT1051TK CAN transceiver with selectable 120 Ω termination, and a microSD slot. Power architecture supports up to 6S battery input with TVS protection, dedicated 5 V and 9 V switching regulators (the latter for digital VTX systems), and separate 3.3 V LDOs (AP7361C-33) isolating the MCU and sensor rails. Two ESC connectors carry eight motor outputs plus current sensing and telemetry UARTs. [1] [2]
What we checked
Source review only. Upstream explicitly marks this design as unvalidated pre-production hardware. No ERC/DRC run, PCB fabrication, or flight test was performed. No local image asset is bundled yet.
Not yet established
- Requirements: operating system, host computer
- A step-by-step setup summary
Updates
Source files and licenses
Complete CERN-OHL-S-2.0 six-layer KiCad STM32H743 flight controller with editable schematics, PCB layout, STEP model, and JLCPCB/NextPCB BOMs; scoped carefully as partial/pre-production because firmware is external and upstream discloses prototype bring-up and flight testing are pending.
| Layer | Availability / license |
|---|---|
| mechanical design | available · CERN-OHL-S-2.0 3D STEP model (LEVIA_H7.step), board outline DXF (pcb_1.dxf), and Edge_Cuts SVG. [1] [3] |
| electronics | available · CERN-OHL-S-2.0 Complete hierarchical KiCad 10 schematics (13 .kicad_sch files), 6-layer .kicad_pcb, custom .kicad_dru, Gerbers, and JLCPCB/NextPCB BOM/CPL files. [1] [2] [3] |
| firmware | not found · License not fully assessed Hardware-only repository; designed around standard STM32H743 / MatekH743 ArduPilot peripheral conventions, but no firmware or hwdef file is included. [1] |
| documentation | available · CERN-OHL-S-2.0 README, exported schematic PDFs (LEVIA_H7.pdf), and PCB layer renders. [1] [3] |
Standalone flight-controller hardware board; ground-control software is external.
Flight controller hardware design; no ML model weights.
Flight controller hardware design; no datasets.
References
Each source links to the exact revision we read. “Used for” shows where this page relies on it.
- S001 piecol/LEVIA-H7 README.md
Architecture, six-layer stackup, dual ICM-42688-P IMUs, power domains, interfaces, KiCad 10 requirement, and unvalidated prototype warning.Revision, date & where cited
Pierluigi Colangeli · github.com · revision
8be94fc· README.md at · Accessed Nov 21, 2026
Used for: Overview, Is this for you?, What you need, Hardware & parts and 5 more - S002 piecol/LEVIA-H7 jlcpcb/production_files/BOM-LEVIA_H7.csv
Exact LCSC-mapped SMD BOM confirming STM32H743VIHx, dual ICM-42688-P, DPS368, IST8310, AT7456ELAH, SIT1051TK CAN transceiver, and regulators.Revision, date & where cited
Pierluigi Colangeli · github.com · revision
8be94fc· jlcpcb/production_files/BOM-LEVIA_H7.csv at · Accessed Nov 21, 2026
Used for: Overview, Hardware & parts, Assembly & first use, Hardware architecture and manufacturing files and 1 more - S003 piecol/LEVIA-H7 LICENSE.txt
CERN Open Hardware Licence Version 2 - Strongly Reciprocal (CERN-OHL-S-2.0).Revision, date & where cited
Pierluigi Colangeli · github.com · revision
8be94fc· LICENSE.txt at · Accessed Nov 21, 2026
Used for: Overview, Cost, Source files and licenses
Correction guidance · Discussion is not enabled · Profile format 0.7.0-draft.5
Change history
2026-11-21 — Initial source-reviewed draft for Hardware Blind-Spot Batch 1.