Open Source RoboticsRobots, software & learning

OpenTorque Quasi-Direct-Drive (QDD) Actuator

Robot / hardware build

CC-BY-SA-4.0 3D-printable planetary-gear compliant actuator for legged robotics with STEP and STL geometry (including low-backlash gear variants), Polymaker CoPA Nylon print settings, and an 11-line BOM built around a 100 KV brushless motor, THK RA8008 crossed-roller bearing, and AMS AS5048A magnetic encoder. [1] [2] [3] [4]

Build & first use →Official websiteSource codeUpstream build guideBill of materials

For
Legged-robotics builders and mechanical designers prototyping 3D-printable planetary brushless joint actuators. [1] [2]
Cost
No current cost yet. Upstream bill of materials [2]
Source rights
Named licenses are documented by part. Review licenses
Unknowns
host computer, operating system not fully established. Review gaps

Source researched · Not tested by us
Sources checked · Research details

Licenses & related hardware

Requirements · Research details and dates

On this page

Overview

OpenTorque Actuator (G-Levine/OpenTorque-Actuator) is a CC-BY-SA-4.0 3D-printable planetary-gear compliant actuator designed for legged robotics. Rather than a full mechatronic kit with custom PCBs and firmware, the GitHub repository provides a compact mechanical package: two editable STEP assemblies (opentorque.step and low_backlash_gears.step), twelve printable STL parts, an 11-line Bill of Materials.csv, and explicit FDM printing parameters in Print Instructions.txt. [1] [2] [3] [4]

Is this for you?

Use cases
  • Legged robot hip/knee joint actuation
  • Low-cost 3D-printable planetary actuator prototyping

Inferred from README tagline and planetary gear CAD.

[1] [3] · Editorial assessment

Known limitations
  • Repository contains only mechanical CAD (2 STEP, 12 STL), Bill of Materials.csv, and Print Instructions.txt; no motor controller PCB, firmware, software, or step-by-step assembly manual is stored in GitHub.
  • Core electromechanical parts (Herlea X8318S KV100 / Turnigy Multistar 9235 motor, THK RA8008 crossed-roller bearing, AMS AS5048A encoder PCB) and an external BLDC motor controller must be purchased separately; several 2019 vendor links in the BOM may be stale.
  • Repository has been dormant since April 21, 2019 and does not publish torque, gear ratio, mass, or cost figures inside the GitHub text files.
  • Source review only: Nylon 3D printing, gear backlash, thermal limits, and actuator torque performance were not physically tested.

Scoped to inspected GitHub repository contents.

[1] [2] [3] · Editorial assessment

What you need

Dependencies
  • 3D printer capable of printing Nylon (e.g., Polymaker CoPA) and ABS/Polycarbonate with a 0.6 mm nozzle
  • Bought-in BLDC motor (Herlea X8318S KV100 or Turnigy Multistar 9235), THK RA8008 crossed-roller bearing, and AMS AS5048A encoder PCB
  • External brushless motor driver / FOC controller (not bundled in repo)

[2] [3]

Tools
  • FDM 3D printer with 0.6 mm nozzle capable of Nylon (Polymaker CoPA) and ABS/Polycarbonate
  • Heat-set / threaded insert installation tools for Pemnet M3 inserts

[2] [3]

Hardware & parts

Upstream bill of materials [2]

Hardware configuration

3D-printable planetary-gear quasi-direct-drive (QDD) brushless joint actuator

[1] [2]

Actuators
  • Herlea X8318S KV100 (or Turnigy Multistar 9235 100KV) brushless outrunner motor paired with 3D-printed planetary gear stage

[2] [3]

Sensors
  • AMS AS5048A-TS_EK_AB magnetic rotary encoder PCB

[2]

Degrees of freedom

1

Single-axis rotary planetary joint actuator.

[1] [2] · Editorial assessment

Assembly & first use

Open the upstream getting-started guide [3] · Project documentation [1]

Assembly

Combines 12 printed parts (housing, backplate, bearing retainer, encoder cover/magnet holder, 3-piece planet carrier, standard or low-backlash sun/planet gears) with a THK RA8008 crossed-roller bearing, 3x 625ZZ bearings, 3x M5x30 h7 dowel pins, and 30 Pemnet M3 inserts; detailed assembly walkthrough is hosted externally on Hackaday.io.

[1] [2] [3]

Cost

No current, complete configuration-specific build cost has been established for this profile.

3D preview

Preview not available yet. A 3D CAD assembly preview has not been packaged for this hardware entry yet.

Project notes

Mechanical hardware, BOM, and Nylon printing requirements

The printable mechanical design comprises the actuator housing, backplate, bearing retainer, encoder cover and magnet holder, a three-part planet carrier (Planet Carrier A/B/C), and both standard and low-backlash variants of the sun and planet gears. Bill of Materials.csv pairs those printed parts with off-the-shelf high-load components: a Herlea X8318S KV100 (or Turnigy Multistar 9235 100KV) brushless outrunner motor, a THK RA8008 crossed-roller output bearing, three 625ZZ bearings, three Misumi MSH5-30 (M5×30 h7) steel dowel pins, an AMS AS5048A-TS_EK_AB magnetic encoder PCB, 30 Pemnet M3 threaded inserts (3× IUB-M3-1, 27× IUB-M3-2), and metric hex cap/flat-head screws. [1] [2]

Because the planetary geartrain is printed, Print Instructions.txt specifies strict material and slicing settings: a 0.6 mm nozzle, four perimeters, ≤0.2 mm layer height for the sun gear, planet gears, and actuator housing (≤0.4 mm for remaining parts), 100% infill for the sun and planet gears (50% cubic infill for all other parts), Nylon (Polymaker CoPA recommended) for the gears and housing, and Nylon, ABS, or polycarbonate for the remaining structural parts. [3]

Missing electronics, dormancy, and review boundaries

No brushless motor driver PCB, firmware, control software, torque/gear-ratio datasheet, or step-by-step assembly manual is stored inside the GitHub repository (external narrative documentation is linked on Hackaday.io). The repository has been dormant since April 21, 2019, and several 2019 supplier URLs in Bill of Materials.csv—along with current unit cost—were not independently verified or repriced. This review inspected only the pinned revision (412762e9a4ca); no Nylon printing, assembly, or torque testing was performed. [1] [2] [4]

What we checked

Source review only at commit 412762e9a4ca. No Nylon printing, assembly, or actuator testing was performed. No local image asset is bundled yet.

Not yet established

  • Requirements: operating system, host computer
  • A step-by-step setup summary

Updates

Upstream last updated
Apr 21, 2019 [1]
Latest release
Not established
Profile updated
Nov 21, 2026
Sources last checked
Nov 21, 2026
Next review
Feb 19, 2027
Reviewed revision
412762e · repository

Source files and licenses

CC-BY-SA-4.0 3D-printable planetary-gear actuator with editable STEP assemblies, low-backlash gear STLs, itemized BOM, and Nylon print settings; scoped partial because motor controller electronics, firmware, and narrative assembly docs are external and the repo has been dormant since 2019.

LayerAvailability / license
mechanical designavailable · CC-BY-SA-4.0
Editable STEP assemblies (opentorque.step, low_backlash_gears.step) and 12 STL parts under CC-BY-SA-4.0. [1] [4]
electronicsnot found · License not fully assessed
Uses bought-in AMS AS5048A-TS_EK_AB encoder PCB and external motor controller; no custom PCB schematics/layouts in repository. [1] [2]
firmwarenot found · License not fully assessed
No motor-controller firmware is stored in the repository. [1]
documentationavailable · CC-BY-SA-4.0
In-repo Print Instructions.txt, Bill of Materials.csv, and exploded view image; narrative project logs live externally on Hackaday.io. [1] [3] [4]

Standalone mechanical actuator module; control software is external.

Mechanical actuator hardware; no ML model weights.

Mechanical actuator hardware; no datasets.

References

Each source links to the exact revision we read. “Used for” shows where this page relies on it.

Correction guidance · Discussion is not enabled · Profile format 0.8.0-draft.1

Change history

2026-11-21 — Initial source-reviewed Open Spec 0.8.0-draft.1 profile for Hardware Blind-Spot Batch 2.