Raptor pellet extruder
Based on published sources · Not tested by us ·
Overview
Specifications
| Detail | Description |
|---|---|
| Type | Pellet extrusion Source-researched; no physical verification. Editorial assessment [S001] [S002] [S003] · Checked 2026-09-30 |
| Intended users | Builders evaluating this tooling design and its integration requirements Editorial assessment [S001] [S002] [S003] · Checked 2026-09-30 |
| Assembly | Parts workbook includes machined screw/heat block and unpriced lab fasteners. It is not a fresh complete quote. Determine moving mass, heater control, flow calibration, pellet feed and orientation limits. Known prerequisites and unresolved assembly decisions; not a complete build instruction. Editorial assessment [S001] [S002] [S003] · Checked 2026-09-30 |
| Calibration | Not known |
| Operating system | Not known |
| Computer needed | Not known |
3D preview
Preview not available yet. A model has not yet been prepared and approved for display on this page. This does not mean the project lacks CAD files; see Source files and licenses for the reviewed source availability.
Assembly and use
Mounting and application
Documented Ender-3 conversion. As an editorial adaptation assessment, robot-arm use would require evaluating mounting and motion/extrusion synchronization. The inspected evidence establishes no robot-arm interface. [S001] [S002] [S003]
Before sourcing the build
The preserved Parts List/Complete Parts List.xlsx lists an extrusion screw and heat block, plus bolts with unpriced cost cells. Confirm manufacturing requirements and a complete purchasing list; the workbook does not establish a current delivered budget. [S004] Determine moving mass, heater control, flow calibration, pellet feed and orientation limits. [S001] [S002] [S003]
Files and reuse terms
The root license is MIT. It does not establish source availability or reuse rights for every separately sourced control or purchased component. Complete matched electronics, firmware and software source sets remain unestablished, without implying that such files are absent. [S001] [S002] [S003]
The pinned inventory lists SolidWorks assemblies and parts, STL files and a DXF bracket, including screw, barrel and heat-block geometry. These are adaptation starting points, not fabrication-validated parts. They do not establish a complete, matched mechanical and control package. Current delivered cost and measured performance are not established; no hardware was built or tested for this profile.
Cost
No current, complete configuration-specific build cost has been established for this profile.
Source files and licenses
MIT root license. Parts workbook includes machined screw/heat block and unpriced lab fasteners. It is not a fresh complete quote. Determine moving mass, heater control, flow calibration, pellet feed and orientation limits.
| Layer | Availability / license |
|---|---|
| mechanical design | available · MIT MIT root license. Availability refers to the scoped files described here, not a complete configuration-matched manufacturing pack. [S001] [S002] [S003] |
| electronics | not found · License not fully assessed A complete revision-matched source set for this tooling configuration was not established in the inspected documents. Standalone controls and purchased components require separate review; this is not a claim that no code or electronic files exist. [S001] [S002] [S003] |
| firmware | not found · License not fully assessed A complete revision-matched source set for this tooling configuration was not established in the inspected documents. Standalone controls and purchased components require separate review; this is not a claim that no code or electronic files exist. [S001] [S002] [S003] |
| software | not found · License not fully assessed A complete revision-matched source set for this tooling configuration was not established in the inspected documents. Standalone controls and purchased components require separate review; this is not a claim that no code or electronic files exist. [S001] [S002] [S003] |
| documentation | available · License not fully assessed MIT root license. Availability refers to the scoped files described here, not a complete configuration-matched manufacturing pack. [S001] [S002] [S003] |
This profile scopes hardware tooling, without selecting a learned controller or training dataset.
References
Links identify the documentation and revisions used in this profile. Access dates record when each source was retrieved.
- S001 · VidetteMakes
Raptor pellet extruder pinned tree
Accessed 2026-09-30 · e56dc2122e1691c72b03b0565a40a83ac1123f0bSource notes
Evidence for the scoped draft design assessment.
- S002 · VidetteMakes
Raptor pellet extruder / LICENSE
Accessed 2026-09-30 · e56dc2122e1691c72b03b0565a40a83ac1123f0b LICENSESource notes
Evidence for the scoped draft design assessment.
- S003 · VidetteMakes
Raptor pellet extruder / README.md
Accessed 2026-09-30 · e56dc2122e1691c72b03b0565a40a83ac1123f0b README.mdSource notes
Evidence for the scoped draft design assessment.
- S004 · VidetteMakes / RaptorExtruder contributors
Complete Parts List workbook
Accessed 2026-09-30 · e56dc2122e1691c72b03b0565a40a83ac1123f0b; Sheet1 rows 5, 7, 14–16Source notes
Lists screw and heat block quantities and several unpriced bolt rows; not a complete current quote.
Correction guidance · Discussion is not enabled · Profile format 0.6.0-draft.1
Change history
2026-09-30 — Classified in the end-effector hierarchy with cited mechanism and platform evidence; build and rights limitations retained.