SideKick Desktop Liquid Handler
End effectorCERN-OHL-S-2.0 peer-reviewed (HardwareX 2022) 3D-printed desktop SBS microplate liquid dispenser using a two-stepper armature, four 10 µL solenoid positive-displacement pumps, and Raspberry Pi Pico MicroPython USB serial control. [1] [2] [3] [4]
Build & first use →Official websiteSource codeUpstream build guideBill of materials
- For
- Chemistry/biology research labs and university teaching laboratories seeking a compact, non-gantry open-source liquid dispenser. [1]
- Cost
- No current cost yet. Upstream bill of materials [3]
- Source rights
- Named licenses are documented by part. Review licenses
- Unknowns
- host computer, operating system not fully established. Review gaps
Source researched · Not tested by us
Sources checked · Research details
Licenses & related hardware
- License
- CERN-OHL-S-2.0 · Details by part
Overview
SideKick (rodolfokeesey/Liquid-Handler) is a compact, 3D-printed desktop liquid dispensing robot compatible with standard SBS microplates, published in *HardwareX* (2022, DOI 10.1016/j.ohx.2022.e00319) by Rodolfo Keesey, R. LeSeur, and J. Schrier. Rather than a Cartesian rail gantry, SideKick uses a planar armature driven by two stepper motors and four calibration-free solenoid positive-displacement pumps delivering 10 µL increments. Note that Pico_Snapshot/Sidekick_object.py contains conflicting comments on the steppers: self.stepsize = .1125 is commented as 8 microsteps at 0.9 degree motor, whereas the motor-pin section below is commented # 1.8 degree steppers; the actual motor step angle and microstepping setup should be confirmed against the BOM and wiring guide before building. [1] [3]
Is this for you?
- Use cases
- Automated liquid dispensing into standard SBS microplates (e.g., 96-well plates)
- Pedagogical introductions to laboratory automation
- Known limitations
- Dispensing volume is quantized to 10 µL increments via four solenoid positive-displacement pumps.
- The repository includes PCB/SideKickV3.fzz and PCB/SideKickV3.zip, but their internal contents and editability were not opened or verified in this source review.
- CAD format coverage is uneven: 50ml Tube Holder.stl appears only as STL, and Motor Cap New (Unvalidated) appears only as .f3d and .step (no .stl).
- Pico_Snapshot/Sidekick_object.py contains conflicting stepper comments (stepsize = 0.1125 commented as 8 microsteps at 0.9 deg motor vs. motor setup commented as 1.8 deg steppers); verify actual motor angle and microstepping against the BOM/wiring guide.
- In Pico_Snapshot/main.py, an upstream comment warns that G-code dispensing moves "center" rather than individual pump nozzles over the target coordinate ("probably not the desired operation"), whereas native "p" commands target a specific pump and well.
- Upstream $710 total build price reflects the 2022 HardwareX publication and Bill_of_Materials_2_18_22.xlsx; it was not independently repriced in 2026.
- Source review only: 3D printing, mechanical assembly, MicroPython flashing, and dispensing volume accuracy were not physically tested.
What you need
Hardware & parts
Upstream bill of materials [3]
- Hardware configuration
3D-printed desktop armature-based SBS microplate liquid dispensing robot
- Actuators
- 2x stepper motors (Pico_Snapshot/Sidekick_object.py comments conflict between 0.9-degree at 8 microsteps and 1.8-degree steppers; configured stepsize is 0.1125)
- 4x calibration-free solenoid-driven positive-displacement pumps (10 µL increments)
Sidekick_object.py comments disagree on 0.9-degree vs 1.8-degree steppers.
Assembly & first use
Cost
No current, complete configuration-specific build cost has been established for this profile.
Cost, electronics scope, licensing, and review boundaries
Upstream reports a $710 total build cost in the 2022 README and includes Supporting_Documentation/Bill_of_Materials_2_18_22.xlsx alongside assembly_guide.pdf; that 2022 price was not independently repriced in 2026. The repository tree includes two PCB artifacts—PCB/SideKickV3.fzz and PCB/SideKickV3.zip—whose internal contents and editability were not opened or verified in this source review. All files are licensed under CERN-OHL-S-2.0 (license.txt), which requires maintaining the Source Location visibly on produced hardware where practicable and logging design modifications in Supporting_Documentation/CHANGES.txt. This review inspected only the pinned revision (f799c0fc02f2, last updated February 2023); no 3D printing, wiring, or dispensing volume verification was performed. [1] [3] [4] [5]
3D preview
Preview not available yet. A 3D CAD assembly preview has not been packaged for this hardware entry yet.
Model sources
A 3D CAD assembly preview has not been packaged for this hardware entry yet.
Project notes
Mechanical CAD, MicroPython control, and code-level caveats
The repository provides mechanical CAD in 3D_Assets/ across Fusion 360 (.f3d), .step, and .stl formats for most components (base, PCB tray, button housing, four armature links, motor/switch mounts, and a 96-well plate holder). Coverage is not uniform across every part: 50ml Tube Holder.stl is listed only as an STL, and one motor-mount revision is explicitly named Motor Cap New (Unvalidated) with .f3d and .step files (no listed .stl). [3]
Control runs directly on a Raspberry Pi Pico in MicroPython (Pico_Snapshot/) over a USB serial terminal, supporting simple interactive commands (initialize, remap, manual purge, execute saved protocol), native pump-well-volume commands (p...), and G-code equivalents (G28, G29, M17, M18, M24). Inspecting Pico_Snapshot/main.py surfaces an important operational caveat: the G-code dispense branch moves "center" to (x, y) before firing pumps and carries an explicit upstream comment warning that this is "probably not the desired operation" compared with native p commands that target individual pump offsets. [1] [2]
What we checked
Source review only at commit f799c0fc02f2. No 3D printing, Pico flashing, wiring, or dispensing test was performed. No local image asset is bundled yet.
Not yet established
- Requirements: operating system, host computer
- A step-by-step setup summary
Updates
Source files and licenses
Peer-reviewed CERN-OHL-S-2.0 desktop SBS microplate liquid dispenser with Fusion 360/STEP/STL CAD, MicroPython Pico firmware, BOM spreadsheet, and assembly PDF; scoped partial because PCB/SideKickV3.fzz and PCB/SideKickV3.zip contents were not verified, CAD format coverage is uneven (50ml Tube Holder is STL-only and one motor cap is unvalidated), and firmware has documented stepper-comment and G-code offset caveats.
| Layer | Availability / license |
|---|---|
| mechanical design | available · CERN-OHL-S-2.0 Editable Fusion 360 (.f3d), STEP, and STL files for main body, four-link armature, motor mounts, and 96-well tray/50 mL tube holders under CERN-OHL-S-2.0. [3] [4] |
| electronics | available · CERN-OHL-S-2.0 PCB/SideKickV3.fzz and PCB/SideKickV3.zip are present in the repository under CERN-OHL-S-2.0, but their internal contents and editability were not opened or verified in this review. [3] [4] |
| firmware | available · CERN-OHL-S-2.0 MicroPython controller code (main.py, Sidekick_object.py, kinematicsfunctions.py, parser.py, plategen.py) under repository CERN-OHL-S-2.0 terms. [2] [3] [4] |
| documentation | available · CERN-OHL-S-2.0 Assembly guide PDF, PuTTY serial example PDF, BOM spreadsheet, CHANGES.txt, and HardwareX 2022 paper (DOI 10.1016/j.ohx.2022.e00319). [1] [3] [4] [5] |
Operated directly over USB serial terminal (e.g., PuTTY) without a separate host GUI.
Deterministic lab liquid dispenser; no ML model weights.
Lab-automation hardware repository; no ML datasets.
References
Each source links to the exact revision we read. “Used for” shows where this page relies on it.
- S001 rodolfokeesey/Liquid-Handler README.md
SBS microplate-compatible desktop liquid dispenser, armature motion, 3D-printed chassis, four 10 uL solenoid positive-displacement pumps, MicroPython USB serial control, $710 publication price, HardwareX 2022 DOI, and CERN-OHL-S v2 notice.Revision, date & where cited
Rodolfo Keesey · github.com · revision
f799c0f· README.md at · Accessed Nov 21, 2026
Used for: Overview, Is this for you?, What you need, Hardware & parts and 5 more - S002 rodolfokeesey/Liquid-Handler Pico_Snapshot/main.py
MicroPython serial command loop supporting custom pump commands and G-code equivalents (G28/G29/M17/M18/M24), plus explicit upstream caveat in G-code dispensing handler.Revision, date & where cited
Rodolfo Keesey · github.com · revision
f799c0f· Pico_Snapshot/main.py at · Accessed Nov 21, 2026
Used for: Is this for you?, What you need, Hardware & parts, Assembly & first use and 2 more - S003 rodolfokeesey/Liquid-Handler Pico_Snapshot/Sidekick_object.py
MicroPython machine.Pin stepper control (two 1.8-degree steppers, 8 microsteps) and plate lookup map; repository tree confirms 19 .f3d, 19 .step, 19 .stl CAD files (including one labeled Unvalidated), BOM xlsx, and assembly_guide.pdf.Revision, date & where cited
Rodolfo Keesey · github.com · revision
f799c0f· Pico_Snapshot/Sidekick_object.py at · Accessed Nov 21, 2026
Used for: Overview, Is this for you?, What you need, Hardware & parts and 4 more - S004 rodolfokeesey/Liquid-Handler license.txt
CERN Open Hardware Licence Version 2 - Strongly Reciprocal (CERN-OHL-S-2.0).Revision, date & where cited
Rodolfo Keesey · github.com · revision
f799c0f· license.txt at · Accessed Nov 21, 2026
Used for: Cost, Source files and licenses - S005 rodolfokeesey/Liquid-Handler Supporting_Documentation/CHANGES.txt
CERN-OHL-S v2 modification log instructions.Revision, date & where cited
Rodolfo Keesey · github.com · revision
f799c0f· Supporting_Documentation/CHANGES.txt at · Accessed Nov 21, 2026
Used for: Cost, Source files and licenses
Correction guidance · Discussion is not enabled · Profile format 0.8.0-draft.1
Change history
2026-11-21 — Initial source-reviewed Open Spec 0.8.0-draft.1 profile for Hardware Blind-Spot Batch 2.