Voron Stealthburner
Based on published sources · Not tested by us ·
Overview
Filament toolhead platform with CAD and printable housings for a printer extrusion assembly. [S001] [S002] [S003]
Stealthburner is a printer toolhead platform with CAD and printable housings for selected extrusion hardware. Adapting it to an arm or delta robot is an engineering proposal in this profile; the inspected evidence does not establish that mounting interface. [S001] [S003]
Specifications
| Detail | Description |
|---|---|
| Type | Filament extrusion Source-researched; no physical verification. Editorial assessment [S001] [S002] [S003] · Checked 2026-09-30 |
| Intended users | Builders evaluating this tooling design and its integration requirements Editorial assessment [S001] [S002] [S003] [S004] [S005] [S006] [S007] · Checked 2026-09-30 |
| Assembly | Choose exact extruder/hotend combination; separate printed enclosure from purchased melt hardware. Add temperature feedback, cooling, moving mass and extrusion synchronization evidence. Known prerequisites and unresolved assembly decisions; not a complete build instruction. Editorial assessment [S001] [S002] [S003] [S004] [S005] [S006] [S007] · Checked 2026-09-30 |
| Calibration | Not known |
| Operating system | Not known |
| Computer needed | Not known |
3D preview
Preview not available yet. A model has not yet been prepared and approved for display on this page. This does not mean the project lacks CAD files; see Source files and licenses for the reviewed source availability.
Assembly and use
Three separate part selections
First choose the printer: its X carriage files live in that printer’s repository. Then select the hotend-specific front files and either rear_cw1 or rear_cw2 for the original Clockwork or Clockwork2 extruder. These choices must agree before treating the printhead as one assembly. [S004] [S005]
The Rapido mount is one documented example, not a universal parts list. It uses front/rear printed halves, heat-set inserts, four M2.5×8 screws from the hotend kit, two M3×12 screws and PTFE tube. The supported-hotend table excludes Rapido UHF. Rapido V2 has additional wire-location and orientation guidance; select its matching instructions rather than assuming all Rapido versions assemble identically. [S005] [S006] [S007]
Adaptation and source coverage
For a proposed robot adaptation, this review has not established moving mass, temperature-feedback integration, cooling arrangements or motion/extrusion synchronization. Obtain those specifications and a mount/control design for the selected printer carriage, extruder and hotend combination before claiming a working robot tool.
The root repository license is GPL-3.0. Complete revision-matched electronics, firmware and software sources for the proposed adapted configuration remain unverified, and purchased components need their own rights review. That does not establish that control or electronic files are absent. No complete current setup cost or hardware test is claimed. [S002]
Cost
No current, complete configuration-specific build cost has been established for this profile.
Source files and licenses
GPL-3.0 root; purchased hotend, heater and extruder components retain their own scope. Choose exact extruder/hotend combination; separate printed enclosure from purchased melt hardware. Add temperature feedback, cooling, moving mass and extrusion synchronization evidence.
| Layer | Availability / license |
|---|---|
| mechanical design | available · GPL-3.0 GPL-3.0 root; purchased hotend, heater and extruder components retain their own scope. Availability refers to the scoped files described here, not a complete configuration-matched manufacturing pack. [S001] [S002] [S003] [S004] [S005] [S006] [S007] |
| electronics | not found · License not fully assessed A complete revision-matched source set for this tooling configuration was not established in the inspected documents. Standalone controls and purchased components require separate review; this is not a claim that no code or electronic files exist. [S001] [S002] [S003] [S004] [S005] [S006] [S007] |
| firmware | not found · License not fully assessed A complete revision-matched source set for this tooling configuration was not established in the inspected documents. Standalone controls and purchased components require separate review; this is not a claim that no code or electronic files exist. [S001] [S002] [S003] [S004] [S005] [S006] [S007] |
| software | not found · License not fully assessed A complete revision-matched source set for this tooling configuration was not established in the inspected documents. Standalone controls and purchased components require separate review; this is not a claim that no code or electronic files exist. [S001] [S002] [S003] [S004] [S005] [S006] [S007] |
| documentation | available · License not fully assessed GPL-3.0 root; purchased hotend, heater and extruder components retain their own scope. Availability refers to the scoped files described here, not a complete configuration-matched manufacturing pack. [S001] [S002] [S003] [S004] [S005] [S006] [S007] |
This profile scopes hardware tooling, without selecting a learned controller or training dataset.
References
Links identify the documentation and revisions used in this profile. Access dates record when each source was retrieved.
- S001 · VoronDesign
Voron Stealthburner pinned tree
Accessed 2026-09-30 · 8bcb9c246fac19d8ac03931ef97fa07c5e5f0f2bSource notes
Evidence for the scoped draft design assessment.
- S002 · VoronDesign
Voron Stealthburner / LICENSE
Accessed 2026-09-30 · 8bcb9c246fac19d8ac03931ef97fa07c5e5f0f2b LICENSESource notes
Evidence for the scoped draft design assessment.
- S003 · VoronDesign
Voron Stealthburner / README.md
Accessed 2026-09-30 · 8bcb9c246fac19d8ac03931ef97fa07c5e5f0f2b README.mdSource notes
Evidence for the scoped draft design assessment.
- S004 · VoronDesign
STLs/README.md
Accessed 2026-09-30 · 8bcb9c246fac19d8ac03931ef97fa07c5e5f0f2b STLs/README.mdSource notes
Build and artifact context for the selected design.
- S005 · VoronDesign
STLs/Stealthburner/Printheads/README.md
Accessed 2026-09-30 · 8bcb9c246fac19d8ac03931ef97fa07c5e5f0f2b STLs/Stealthburner/Printheads/README.mdSource notes
Build and artifact context for the selected design.
- S006 · VoronDesign
STLs/Stealthburner/Printheads/phaetus_rapido/README.md
Accessed 2026-09-30 · 8bcb9c246fac19d8ac03931ef97fa07c5e5f0f2b STLs/Stealthburner/Printheads/phaetus_rapido/README.mdSource notes
Build and artifact context for the selected design.
- S007 · VoronDesign
STLs/Stealthburner/Printheads/phaetus_rapido_v2/README.md
Accessed 2026-09-30 · 8bcb9c246fac19d8ac03931ef97fa07c5e5f0f2b STLs/Stealthburner/Printheads/phaetus_rapido_v2/README.mdSource notes
Build and artifact context for the selected design.
Correction guidance · Discussion is not enabled · Profile format 0.6.0-draft.1
Change history
2026-09-30 — Classified in the end-effector hierarchy with cited mechanism and platform evidence; build and rights limitations retained.