StealthChanger Kinematic Gantry Tool Changer
End effectorGPL-3.0 passive bushing-and-pin kinematic tool-changing system for Voron and front-mount gantry motion systems, with STEP/STL CAD for V1.1 shuttles and 10+ toolhead backplates, BOMs, and Klipper configs. [1] [2] [3]
Build & first use →Official websiteSource codeUpstream build guideBill of materials
- For
- Voron and CoreXY gantry builders adding multi-toolhead passive kinematic tool changing under Klipper. [1] [3]
- Cost
- No current cost yet. Upstream bill of materials [1] [2]
- Source rights
- Named licenses are documented by part. Review licenses
- Unknowns
- host computer, operating system not fully established. Review gaps
Source researched · Not tested by us
Sources checked · Research details
Licenses & related hardware
- License
- GPL-3.0 · Details by part
Overview
StealthChanger is a GPL-3.0 passive kinematic tool-changing system from DraftShift Design (derived from Viesturz's TapChanger) for Voron and other front-mounted gantry motion platforms. Instead of bearing-and-alignment assemblies, it uses a printed shuttle fitted with three 4 × 6 × 6 mm brass bushings and three 6 × 3 mm N52 magnets that mate passively with three Ø4 × 12 mm rounded steel dowel pins and a magnet on each toolhead backplate. [1] [2] [5]
Is this for you?
- Use cases
- Multi-toolhead 3D printing on Voron and front-mount gantry systems
- Known limitations
- V1.1 shuttles and backplates are not backward-compatible with earlier StealthChanger versions.
- Requires filament-specific shrinkage calibration (e.g., Califlower) due to tight tolerances; long-term wear life of brass bushings and steel pins is still being tested upstream.
- Requires external klipper-toolchanger plugin and TapChanger Klipper configuration files, plus an OptoTap optical sensor PCB per toolhead.
- Xol and A4T toolhead backplates require replacing stock Voron 2.4 Z joints with lower-profile alternatives to prevent bottoming out.
What you need
Hardware & parts
Assembly & first use
Open the upstream getting-started guide [1] · Project documentation [1]
- Calibrate filament shrinkage and print the V1.1 shuttle (with build-plate supports) and matching toolhead backplates to Voron print standards.
- Source shuttle hardware (3x 6x3 mm N52 magnets, 3x 4x6x6 mm brass bushings, M3 fasteners) and per-toolhead backplate parts (3x 4x12 mm dowel pins, N52 magnet, magnetic FHCS screws, OptoTap sensor PCB).
- Assemble shuttle, backplates, and docks following Manual/Stealthchanger_Assembly_Guide.pdf and wiki guides.
- Install viesturz/klipper-toolchanger and configure homing, tool detection, and per-toolhead macros in Klipper.
Cost
No current, complete configuration-specific build cost has been established for this profile.
Cost and review boundaries
wiki/Bill-of-Materials.md itemizes per-shuttle and per-toolhead hardware with affiliate supplier links, but no unified build cost is published because totals scale with toolhead count, dock choice, and umbilical hardware. Upstream also notes that long-term wear life of the brass bushings and steel pins is still under test. This review inspected only the pinned revision (50e3c769297b); no parts were printed, assembled, or measured for docking repeatability. [1] [2]
3D preview
Preview not available yet. The upstream design is linked below. An interactive preview has not been prepared for this profile.
Model sources
The upstream design is linked below. An interactive preview has not been prepared for this profile.
Project notes
Hardware compatibility, printing, and Klipper integration
The pinned repository includes editable STEP files (CAD/), print-oriented STLs (STLs/), an illustrated assembly guide (Manual/Stealthchanger_Assembly_Guide.pdf), in-repo wiki documentation (wiki/), and an extensive UserMods/ tree. Supported toolhead backplates listed in the pinned README include StealthBurner, DragonBurner, RapidBurner, Yavoth, AntHead, A4T, XOL, Jabberwocky, and Archetype BlackBird, plus community mods. Each toolhead backplate also mounts an OptoTap optical sensor PCB and magnetic flat-head countersunk screws for probe/dock detection. [1] [2]
Builders should note three upstream constraints: V1.1 shuttles and backplates are incompatible with earlier revisions; tight coupling tolerances require per-filament shrinkage calibration before printing (with the shuttle printed flat using build-plate supports); and XOL/A4T backplates require lower-profile Z joints on Voron 2.4 frames to avoid bottoming out. Software control relies on Klipper with the external viesturz/klipper-toolchanger plugin and TapChanger configuration structure. [1] [2] [3] [4]
What we checked
Source review only. No parts were printed, assembled, or tested for docking repeatability or input-shaper rigidity. No local image asset is bundled yet.
Not yet established
- Requirements: operating system, host computer
Updates
Source files and licenses
Extensive GPL-3.0 passive kinematic tool-changer hardware design with editable STEP/STL CAD, BOM, assembly manual, and Klipper config examples; partial because optical sensing uses bought-in OptoTap PCBs and motion control requires external klipper-toolchanger software.
| Layer | Availability / license |
|---|---|
| mechanical design | available · GPL-3.0 Editable STEP files for V1.1 shuttle and 10+ toolhead backplates in CAD/ plus print-oriented STLs in STLs/ and UserMods/. [1] [5] |
| electronics | available · GPL-3.0 Community LED PCB KiCad/Gerber/BOM files in UserMods/; core optical tool detection relies on bought-in OptoTap sensor PCBs. [1] [5] |
| software | available · GPL-3.0 Example Klipper configuration files in Klipper/; requires external viesturz/klipper-toolchanger plugin. [1] [3] [5] |
| documentation | available · GPL-3.0 In-repo wiki markdown guides, assembly PDF manual, and printing instructions. [1] [2] [4] [5] |
Passive mechanical tool-changing coupling; relies on host printer Klipper firmware.
Mechanical tool-changer hardware; no ML model weights.
Mechanical tool-changer hardware; no datasets.
References
Each source links to the exact revision we read. “Used for” shows where this page relies on it.
- S001 DraftShift/StealthChanger README.md
Design rationale (bushing-and-pin passive coupling), supported toolheads, V1.1 incompatibility notice, and Tapchanger lineage.Revision, date & where cited
DraftShift Design · github.com · revision
50e3c76· README.md at · Accessed Nov 21, 2026
Used for: Overview, Is this for you?, Hardware & parts, Assembly & first use and 4 more - S002 DraftShift/StealthChanger wiki/Bill-of-Materials.md
Shuttle and per-toolhead backplate BOM (N52 magnets, 4x6x6 mm brass bushings, 4x12 mm dowel pins, OptoTap PCB, magnetic FHCS screws, and Z-joint caveats).Revision, date & where cited
DraftShift Design · github.com · revision
50e3c76· wiki/Bill-of-Materials.md at · Accessed Nov 21, 2026
Used for: Overview, Is this for you?, What you need, Hardware & parts and 4 more - S003 DraftShift/StealthChanger Klipper/README.md
Dependency on viesturz/klipper-toolchanger and TapChanger Klipper configuration structure.Revision, date & where cited
DraftShift Design · github.com · revision
50e3c76· Klipper/README.md at · Accessed Nov 21, 2026
Used for: Is this for you?, What you need, Assembly & first use, Hardware compatibility, printing, and Klipper integration and 1 more - S004 DraftShift/StealthChanger wiki/Printing.md
Voron print settings, per-filament shrinkage calibration requirement, and shuttle support orientation.Revision, date & where cited
DraftShift Design · github.com · revision
50e3c76· wiki/Printing.md at · Accessed Nov 21, 2026
Used for: Is this for you?, What you need, Assembly & first use, Hardware compatibility, printing, and Klipper integration and 1 more - S005 DraftShift/StealthChanger LICENSE
Root GNU General Public License v3.0.Revision, date & where cited
DraftShift Design · github.com · revision
50e3c76· LICENSE at · Accessed Nov 21, 2026
Used for: Overview, Source files and licenses
Correction guidance · Discussion is not enabled · Profile format 0.7.0-draft.5
Change history
2026-11-21 — Initial source-reviewed draft for Hardware Blind-Spot Batch 1.